Special Effect Basecoat Colour
A range of multi-flip pearls as a result will give a two tone effect and in addition a range of superb pearls and metallics with a Deep shimmering colours with high reflectivity in sunlight and a range of solid colours used with clearcoat or as a base for pearls and metallics colours.
A new range of designer colours are also available mixed to order. for car and commercial vehicles and furthermore is brilliant on cycles,motorbikes scooters and any exterior item.
The range of products has been design to make the application of Metallic and Pearlcoat colours a simple process , due to the ease of application and will stop the problems associated with application of basecoat ,mottling of Metallic, long drying times and Floating when lacquer is applied over basecoat are all things of the past.
Metallic and pearlcoat Products
Mirrorbase Polyester base coat clearcoat system
Mirrorbase should be used as part of refinishing systems and should be over coated with Mirrorclear clearcoat product before protection is achieved. Quick drying basecoat available in solid, metallic, pearl and special effect multi flip due to low opacity most colours will require a coloured groundcoat.
Mirrorbase basecoat is a quick drying basecoat for car and commercial vehicles consequently improving you throughput and efficiency. This product has been design to make the application of Metallics and Pearlcoat colours a simple process , due to the ease of application , Mirrorbase stops the problems associated with application of basecoat ,mottling of Metallics ,long drying times and Floating when lacquer is applied over basecoat are all things of the past. Mirrorbase should be used as part of refinishing systems and should be over coated with Mirrorclear Clearcoat product before protection is achieved. Quick drying basecoat available in solid, metallic, pearl and special effect multi flip.
107.003 – every thinner fast
107.004 – every thinner slow
All original finishes cleaned and sanded (not recommended on thermoplastic acrylic finishes).
Mirror hi-Fil 2k primer.
Mirror Washfiller etch.
Tempo filler shades
Mirrorbase basecoat apply three coats allow to dry between coats then allow 15-20 minutes flash after the application of the last coat before applying Clearcoat.
The entire panel or blending in areas have to be carefully prepared as follows (before basecoat application):
– Clean with water and soap
– Degreaser with mirror quick wipe degreaser.
– Dry sand with p500 disc finish with grey finishing pad.
– Or Wet flat with p1000 wetordry.
– Wipe dry with clean and dry cloth.
– Tack off or Use Attract rag.
Use 1 – 1 ratio mixing stick.
1 part Mirrorbase with 1 part every thinner fast/slow.
Please make sure you add 10% hardener to the colour if not clear coated after flash off times
– Spray viscosity (at 20 °c) Din4 15s.
– Pot life (at 20 °c) 24 hrs
– Gravity feed fluid tip 1.2 – 1.4mm
– Suction fluid tip 1.0 – 1.2mm
– Pressure type fluid tip 1.0 – 1.2mm (Pressure 4 – 6 bar – 50 – 80 psi)
– Spray pressure (bar): 3.5 – 4 (45-50 psi)
– Spray distance (cm): 15-20 cm
10 minutes between coats.
Recoatable with Mirrorclear 2k
30 minutes after last coat application.
After hard dry times of Mirrorclear 2k.
After the application of Mirrorclear 2k.the fully cured coating is resistant to short exposures to the following chemicals:
Sodium hydroxide 20% battery acid 15%
Sulphuric acid 25% toluene 20%
Hydrochloric acid 20% Xylene 20%
Phosphoric acid 20% glycol 20%
Ammonia 10% brake fluid 25%
Use mirror low cost thinner immediately after use.
Please prepare the surface carefully before the Mirrorbase basecoat application.
Protect exteriors or prepare and sand exteriors prior to applying the interiors to prevent re lifting of the over spray when applying the exterior finish.
6 – 8 m2 per ltr per coat at recommended dry film thickness, unactivated
Mirrorbase metallic 15-25 microns
Mirrorbase solid 35-45 microns
Closed original containers stored at normal room temperature
Mirrorbase 2 years