Special Effect Basecoat Colour PI402 WHITE/GREEN FLIP

£0.00

A range of multi-flip pearls as a result will give a two tone effect and in addition a range of superb pearls and metallics with a Deep shimmering colours with high reflectivity in sunlight and a range of solid colours used with clearcoat as a basecoat system for pearls and metallics colours. Basecoat and clear finish, Car, Bike, Coach , Special Effect , Custom Paint & Varnish .

Email
Compare

Description

Special Effect Basecoat Colour

A range of multi-flip pearls as a result will give a two tone effect and in addition a range of superb pearls and metallics with a Deep shimmering colours with high reflectivity in sunlight and a range of solid colours used with clearcoat or as a base for pearls and metallics colours.

A new range of designer colours are also available mixed to order. for car and commercial vehicles and furthermore is brilliant on cycles,motorbikes scooters and any exterior item.

The range of products has been design to make the application of Metallic and Pearlcoat colours a simple process , due to the ease of application and will stop the problems associated with application of basecoat ,mottling of Metallic, long drying times and Floating when lacquer is applied over basecoat are all things of the past.


Metallic and pearlcoat Products

Mirrorbase Polyester base coat clearcoat system

Mirrorbase should be used as part of refinishing systems and should be over coated with Mirrorclear clearcoat product before protection is achieved. Quick drying basecoat available in solid, metallic, pearl and special effect multi flip due to low opacity most colours will require a coloured groundcoat.

Mirrorbase basecoat is a quick drying basecoat for car and commercial vehicles consequently improving you throughput and efficiency. This product has been design to make the application of Metallics and Pearlcoat colours a simple process , due to the ease of application , Mirrorbase stops the problems associated with application of basecoat ,mottling of Metallics ,long drying times and Floating when lacquer is applied over basecoat are all things of the past. Mirrorbase should be used as part of refinishing systems and should be over coated with Mirrorclear Clearcoat product before protection is achieved. Quick drying basecoat available in solid, metallic, pearl and special effect multi flip.

Additives

107.003 – every thinner fast
107.004 – every thinner slow

Substrates

All original finishes cleaned and sanded (not recommended on thermoplastic acrylic finishes).
Mirror hi-Fil 2k primer.
Mirror Washfiller etch.
Tempo filler shades

Surface preparation

Mirrorbase basecoat apply three coats allow to dry between coats then allow 15-20 minutes flash after the application of the last coat before applying Clearcoat.

The entire panel or blending in areas have to be carefully prepared as follows (before basecoat application):
– Clean with water and soap
– Degreaser with mirror quick wipe degreaser.
– Dry sand with p500 disc finish with grey finishing pad.
– Or Wet flat with p1000 wetordry.
– Wipe dry with clean and dry cloth.
– Tack off or Use Attract rag.

Product preparation

Use 1 – 1 ratio mixing stick.

Mix ratio

1 part Mirrorbase with 1 part every thinner fast/slow.

Please make sure you add 10% hardener to the colour if not clear coated after flash off times

Application Data

– Spray viscosity (at 20 °c) Din4 15s.
– Pot life (at 20 °c) 24 hrs
– Gravity feed fluid tip 1.2 – 1.4mm
– Suction fluid tip 1.0 – 1.2mm
– Pressure type fluid tip 1.0 – 1.2mm (Pressure 4 – 6 bar – 50 – 80 psi)
– Spray pressure (bar): 3.5 – 4 (45-50 psi)
– Spray distance (cm): 15-20 cm

Drying times

10 minutes between coats.

Recoatable with Mirrorclear 2k

30 minutes after last coat application.

Recoatability

After hard dry times of Mirrorclear 2k.

Chemical resistance

After the application of Mirrorclear 2k.the fully cured coating is resistant to short exposures to the following chemicals:

Sodium hydroxide 20% battery acid 15%
Sulphuric acid 25% toluene 20%
Hydrochloric acid 20% Xylene 20%
Phosphoric acid 20% glycol 20%
Ammonia 10% brake fluid 25%
Petrol 20%

Equipment cleaning

Use mirror low cost thinner immediately after use.

Remarks

Please prepare the surface carefully before the Mirrorbase basecoat application.

Protect exteriors or prepare and sand exteriors prior to applying the interiors to prevent re lifting of the over spray when applying the exterior finish.

Product data

Theoretical coverage

6 – 8 m2 per ltr per coat at recommended dry film thickness, unactivated
Mirrorbase metallic 15-25 microns
Mirrorbase solid 35-45 microns
Storage stability

Closed original containers stored at normal room temperature
Mirrorbase 2 years

Additional information

Dimensions 115 × 115 × 140 mm
Colour